2016 AMERICAN DAGSTER
Price- $32,500 Roller
This dragster is apart of American Race cars platinum series and is a quality race car. Fully loaded with about every option you can think of makes this car a great deal, with a parachute, air compressor, digital delay box, led dial in board and much more!! With beautiful paint and comfortable seat this car is a great buy.
With 9 degree motor in it over the couple of races this car has been flying with a 182mph at indy in super comp at around 1900lbs and ran a 4.54 all out 1/8th mile and ran numbers back to back. This gorgeous dragster is easy to drive and fun!!
TK $64,900
Willing to buy/trade in may different forms including Turn Key, Roller, with Delta wheels or without, looking for fair and reasonable offers!!
↧
16 American Dragster
↧
1965 Dodge Coronet A990 Tribute
This 1965 Dodge Coronet A990 Tribute is amazing, showroom quality. Complete restoration done in 2012, with less than 200 miles on the new engine. The restoration was done on a rust-free body. There is a 426 hemi engine, 1966 Block, 64-65 Race hemi heads, Roller cam, Roller rockers, 833 Hemi 4 speed transmission, 3000 lb. clutch, 660 lift, 296 Duration, Crower Crank shaft, Nascar Connecting Rods, Arias 12.5 to 1 pistons, Dry Sump Oiling system by Chrysler, Date coded 1965 Cross Ram intake, 3116 Holley Carburetor, Headers 2 1/4 inch primaries, 4inch collector with hand-made Stainless Steel Exhaust-4inch, Electronic ignition, tachometer is cable driven, Aluminum radiator, Aluminum fly wheel, and Dana 60 Rear End with 410 gear.
PPG paint products were used in the restoration. The Paint is a 2009 Jaguar color called Radiance. The paint work has received 2 awards.
↧
↧
1980 chevrolet malibu race car
We can also accept credit cards check & debit cards.
This is a Roller no engine or trans no gauges or electronics or shifter
I took this car in trade it is a 80 Malibu has a braced 9" ford rear end with coil overs triangulated 4 link 145x32 m/t tires convo pro wheels all aluminum inside with funny car cage all factory glass but windshield and rear glass driver side door glass rolls up and down nice black aluminum door panels front stock sub frame with bbc engine plate and mid plate glass hood with pro stock style scoop glass deck lid with a super nice wing front wheels 15x4 with convo pro wheels long wheel studs all the way around . the front fenders has holes cut for headers but have extra fender with no holes in them also have have a extra header panel for the 2 head lights also have a extra front fiberglass bumper and bbc headers and the drive shaft
may take some kind of trade
Call 513-225-0494
Email www.ronowensracing@yahoo.com
↧
2018 Charlie Stewart Crovette Roadster
Beautiful roadster with all of the the best parts, brand new
↧
57 Chevy Drag Car (ROLLER)
57 Chevy Drag Car (ROLLER), Would make a Great Gasser, Back Half, Set up for BB Chevy Engine & PG Trans, (New BBC Headers), Braced 9" 456 Gear with spool, Alum Pinion Support, 4 Link, Wishbone, Front & Mid Engine Plates, Engine Shift Braces, Driveshaft, 2 Driveshaft Loops, Front Disc, Rear Drum, 5/8 Studs Rear, QA1 Coil Overs Rear, Line Lock, BG 400 Fuel Pump with Paxton Fuel Filter, 8 Gal Fuel Cell, Has a Rear Wing, Some Braided Lines, Window Net, Grant Pull off Steering Wheel, Fiberglass Seat with Cover, 14 Point Roll Cage, Charging Studs Rear, 2 Battery Boxes in Trunk, Fiberglass Front End, MSD 6al, High output Coil, Tac with Shift Light, Fuse Block, Gauges, Cooling Fan Inside, Alum Griffin Radiator with Elec Fan, M/T 32X14X15 Slicks, Weld Rims, Lexan on Sides, Glass Front & Rear. Weight 2650 with Alum. Head BB Chevy Engine (no driver). Built to run in the 5s in 1/8 mile.(Needs Batteries, Shifter & Cable & some DZ Fastener adjustment.) Take care of these needs and be racing soon. Should Certify 8.50 Welding on Mild Steel is Very Good. Could use some cleaning that is up to you. Has a few Scratches and Chips, (Has VIN number & Alabama Bill of Sale) *MAKE ME A CASH OFFER* CALL 919-698-1357
↧
↧
80 Mustang
front end has Vin and Florida title
466 big block ford trick flow aluminum heads forged internals 1050 BLP carb on E-85 60-70 lbs oil pressure all MSD ignition 2 speed Power Glide with brake electric shift K&R Pro Cube delay box full exhaust frame tied rear suspension completely adjustable New slicks with 5 passes on them car runs great very consistent 6.40 in the 1/8 too much to list
Also have Trailer 2016 28' with 5' RV tongue all L E D lights inside and out cabinets e-track new spare tire very little mileage on it in great condition
Will make package deal including Ca Am 90 quad
Just hook up and go racing
Car $11,500 Package $17,000
Have Title to car and trailer in hand
↧
65 Malibu SS roller
65 Malibu SS tube chassis drag car.
$5000 FIRM
Rolling chassis only.. no trades
1965 Chevelle Malibu SS ( real 138 car per vin).
Rectangular tube chassis car. Strange strut front suspension, 4 link braced ford 9"( no center section) Strange axles, QA1 double adjustable rears, JFZ disc brakes at all 4 corners, fiberglass nose with removable hood (hood needs to be pinned to fenders still. All aluminum interior with removable trans tunnel and rear suspension panel. 10 point cage, chassis cert 8.50 ran out in 2015, Weld wheels, 32x14x15 slicks, fiberglass doors, fiberglass trunk lid, lexan windows all around (was going to replace side windows so they were removed-still have), fiberglass front and rear bumpers, rack and pinion steering, aluminum radiator and line lock solenoid. Master on off switch and charging jacks on rear bumper.
Car needs paint... small dent on right rear quarter (easy fix). And wiring needs to be upgraded.. Car weighed 2590lbs with iron headed big block and powerglide.
Car comes with NO gauges or switch panel, No Ignition system, No shifter, No fuel system, No Engine or transmission..
Will include aluminum seat and cover, belts, window net, complete set of new HAWK brake pads (over $300 for those), new charging post caps, battery box and hold down, a new Grumpy Lump style hood scoop and some additional windshield mouldings and whatever other odds and ends I collected.
Put your driveline in this and in no time you will be ready to rock and roll. Drag race, street race, grudge or turn it into one heck of a street car!!
Car at one time had a Lenco so clutch pedal is still hanging in the car.
Connecticut does not title cars over 20 years old, so car will be sold with bill of sale only.
Car is located in Brookfield Ct ( about 15 minutes from NY state border taking I-84.)
If more pictures are needed please let me know.. engine still in car until serious buyer shows interest for the rolling chassis. Engine NOT for sale.
↧
1991 TOYOTA MR2 WITH BUILT K24 TURBO SWAP
Turn key 9 second car made 724 hp will go over complete build with a serious buyer everything was purchased new no corners cut
↧
57 Chevy Drag Car (ROLLER)
57 Chevy Drag Car (ROLLER), Would make a Great Gasser, Back Half, Set up for BB Chevy Engine & PG Trans, (New BBC Headers), Braced 9" 456 Gear with spool, Alum Pinion Support, 4 Link, Wishbone, Front & Mid Engine Plates, Engine Shift Braces, Driveshaft, 2 Driveshaft Loops, Front Disc, Rear Drum, 5/8 Studs Rear, QA1 Coil Overs Rear, Line Lock, BG 400 Fuel Pump with Paxton Fuel Filter, 8 Gal Fuel Cell, Has a Rear Wing, Some Braided Lines, Window Net, Grant Pull off Steering Wheel, Fiberglass Seat with Cover, 14 Point Roll Cage, Charging Studs Rear, 2 Battery Boxes in Trunk, Fiberglass Front End, MSD 6al, High output Coil, Tac with Shift Light, Fuse Block, Gauges, Cooling Fan Inside, Alum Griffin Radiator with Elec Fan, M/T 32X14X15 Slicks, Weld Rims, Lexan on Sides, Glass Front & Rear. Weight 2650 with Alum. Head BB Chevy Engine (no driver). Built to run in the 5s in 1/8 mile.(Needs Batteries, Shifter & Cable & some DZ Fastener adjustment.) Take care of these needs and be racing soon. Should Certify 8.50 Welding on Mild Steel is Very Good. Could use some cleaning that is up to you. Has a few Scratches and Chips, (Has VIN number & Alabama Bill of Sale) *MAKE ME A CASH OFFER* CALL 919-698-1357
↧
↧
Door Stands Jerry Bickel
Lightweight aluminum construction
• Designed for easy, fold away storage
• Safe, effective way to store doors when not on race car
• Holds two doors
↧
Wheel Spacers JBRC5069 1/4" Jerry Bickel
spacer 1/4" - Price per pair - Fits bolt patterns 4.5", 4.75" & 5" X 5
↧
Clear Plastic Cleaner & Polish Jerry Bick
Recommended by JBRC for polycarbonate window care. Specially formulated to remove dirt from windows without streaking by using an anti-fogging/anti-static formula that repels dust and restores optical clarity. One-step action saves maintenance time and window surfaces. Highly recommended for cleaning and routine maintenance on polycarbonate windows. 13 oz.
↧
Weathertight Sealed Connector Kit Jerry Bicke
Everything you need to do a professional job. Over 660 pieces with all necessary tools.
↧
↧
Aluminum Pro 2 WC0310 Jerry Bickel
Taking the remote concept a step further, this system integrates the water pump into the radiator for situations where the space on the engine and in the chassis is at a premium. Compared to a traditional remote pump, you save on space, mounting bracket, and inlet plumbing. 1 1/4" upper hose connection. Pump NOT included
↧
Mopar Style Sportsman Master Cylinder Jerry B
Dual 1" master cylinder features aluminum housing, factory mounting hole pattern and outlet thread size, large capacity plastic reservoir, master cylinder push rod and dust boot. These master cylinders can be used with drum or disc brakes. Available in both Pro model and the more economical Sportsman model. Sportsman Model
↧
Complete Guide to Chassis Performance Jerry B
This information packed book contains the knowledge that Jerry has accumulated in his 25 years of drag racing success. Learn how drag slicks work and how to adjust 4-link suspensions and weight transfer for any track conditions. What causes tire shake? How do I eliminate it? No more mysteries about shock absorbers and pre-load settings. It's all between the covers of his newest release in a whole new era of drag racing knowledge.
↧
JBRC 4130 3
Our bullet proof professional driveshaft is constructed of 3" OD x .083 4130 heat treated tubing with precision aligned and welded JBRC 4140 forged steel weld yokes and JBRC solid heavy duty 1350 joints. Every shaft is electronically balanced with the transmission yoke installed. Suitable for all racing applications and highly recommended for high horsepower Pro Stock and Pro Modified cars or the heavy weight race cars.
SFI Certified.
(u-jounts included less yoke)
Should be ordered with yoke for proper balancing.
↧
↧
Braille Super 16 Volt Lithium Battery Combo
PERFORMANCE
Voltage 16 Volts
Minimum Voltage Cutoff: 14 Volts for 30 Sec.
Full Charge Voltage: 17.8 Volts
Maximum Operating Temp Enclosed: 140 Degrees
Maximum Operation Temp Ambient: 165 Degrees
Short Circuit Current: 3000
Pulse Wattage: 3000
Cranking Amps 30 Sec @ 32°F: 1100
Cold Cranking Amps 30 Sec @ 0°F: 575
Reserve Capacity @ 30 amps: 39 Minutes
Amp Hour Capacity: 21-amp hr.
Life Cycle @ 80% DOD: 1000 cycles
PHYSICAL SPECIFICATIONS
Features: Horizontal and Vertical Mounting, Low Voltage Cutoff, Power Button
BCI Group: Same Length as Grouped 34 and Group 24
Length: 11.5”
Width: 3.25”
Height: 6”
Weight: 7.5lbs
Post Type: SAE Automotive Posts include 3/8” Bolt Internal Thread
Recommended Mounting: Secure Mounting with vibration padding on all contact surfaces
CHARGING SYSTEM INCLUDED
Braille Electronic 16 Volt Lithium Charger
Rapid Recharge: 25 amp/hr electronically controlled
Warranty
1 year, Repair/Replacement Warranty. Accidents, Liquids or Physical Damage not covered.
↧
Carbon/Composite Tubs Jerry Bickel
NHRA Approved Composite Wheel Tubs. One Piece Construction. Manufactured from carbon fiber, kevlar and fire resistant resin. Composite construction makes tubs extremely light (11 lbs before trimmed). The unique "D" shape design allows the largest tire without sacrificing aero drag. Tough inner liner adds strength while offering protection from rock damage. When attached to the inner quarter panel this tub makes the rear area of the body extremely strong. Dimensions 46" diameter, 24" height and 29" wide. Priced per pair. Composite
↧
Electric Radiator Fan JBRC5520 Jerry Bickel
Our fan kits contain a heavy-duty, low amperage reversible 12 volt electric motor. The high impact plastic blade will push or pull by simply reversing the polarity. Fan kits are available in 12", 14" and 16".
JBRC5520 12"
↧